Classic Magnetic Frame

I Float glass, glossy, thickness 2.4 mm
II Float glass, matt / glossy, thickness 2.4 mm

Float glass is the first choice if there are no special requirements regarding the glass quality. If contour sharpness is important, a glass with a glossy finish on both sides is recommended. On the other hand, matt finished glass reduces reflections. A combination of both properties is offered by our Optiwhite float glass VI frosted on one side or by the new Mirogard®.

III glossy, with protective film, thickness 3.0 mm
IV antireflective, matt / glossy, with protective film, thickness 3.0 mm

Plexiglass is especially shatter-proof and also protects delicate exhibits against ultraviolet radiation by virtue of its low light transmission. The disadvantages of plexiglass are its low scratch resistance and the somewhat more laborious care with a special antistatic cleaner. The appropriate cleaning agents can be found in our range of accessories.

V Optiwhite float glass, glossy, thickness 2.6 mm
VI Optiwhite float glass, matt / glossy, thickness 2.6 mm

The right choice if a very good, neutral colour reproduction is required. With the Optiwhite float glass VI which is very finely frosted on one side, you have the additional advantage that the contour sharpness of the picture is visibly better than in the case of the antireflective varieties made of float glass or plexiglass.

Schott Mirogard®, specialty glass with optical-interference antireflective coating, thickness 3.0 mm

Mirogard® is a specialty glass with optical-interference antireflective coating on both sides. This means: It is colourless, free of annoying reflections and therefore as good as invisible. One aspect to keep in mind with this high-quality glass type: There should be no distracting effects of light in the surrounding area, such as a window on the opposite side of the picture.

ESG glossy, thickness 4 mm
Single-layer safety glass is a thermally toughened glass which has a higher break and impact resistance. If the glass should nevertheless break due to high stress, it will split into small particles without sharp edges. The risk of injury compared to normal float glass varieties is significantly reduced in this way.

ESG single-sided matt, thickness 4 mm
If, in addition to the advantages of the toughened safety glass, a reflection-reducing view is desired at the same time, then this glass type is the right choice. We have this ESG type produced with the same antireflective surface and glass quality as our float glass II.

VSG glossy, thickness 6 mm
In contrast to the toughened safety glass, the laminated safety glass (VSG) is a composite of 2 glass panes with a thickness of 3 mm each and a PVB film lying inbetween. Due to this thermally created composite, the splitting into small particles in case of a glass breakage is prevented since the VSG binds all glass splinters in the event of a breakage.

This system allows the unobtrusive protection of the picture in the frame. Here, the profile frame is bolted to the base element at the top and at the bottom. The small screws can only be removed with a special tool which is included in the scope of delivery.

The picture safety device BS 1 is appropriate for: Classic magnetic frame, Distance magnetic frame, B1 magnetic frame, Conservo magnetic frame, LED magnetic frame and Passepartout magnetic frame.

Here, the base element is securely bolted down directly to the wall. Your best bet is to combine the picture safety device BS 1 with the picture safety device BS 3 – in this way, picture and frame are perfectly protected at the same time.

BS 1 is appropriate for:
Classic, Distance, B1, Conservo, LED and Passepartout magnetic frames;
BS 3 can be ordered with the Classic, B1, Conservo, Display and Passepartout magnetic frames.

The special feature of this picture safety device is that it is locked by means of a special key in the centre hole of the base element – alternatively at the top, at the bottom or in both centre holes. Using the picture safety device in the lower centre hole is recommended together with the simultaneous use of picture hooks in the two upper hanging holes.

The picture safety device BS 4 is appropriate for:
Classic magnetic frame, Distance magnetic frame, Passepartout magnetic frame and the new Protect magnetic frame.

The standard insertion depth for picture and passepartout (or cardboard) is 2 mm.
If larger insertion depths are required, please indicate them when placing an order.
Special insertion depths are crafted by us without extra charge.

16,0 mm

Classic-Magnetrahmen Zubehör Bestellvordrucke Verschiedenes Katalog/Preisliste